500va transformer for sale, brand-new and used.

500VA 2.9" ID x 4.9 OD x 1.75 H / 10.4 cm(sq) cross section AC Power Transformer Toroidal Core, new type FG steel ( wt. 5.5 lb ) Lot Size: 1 units See other listings and lot sizes for this item

3/4" x 40 yards Heat-Shrink Mylar Tape for toroid transformer binding & coating 3/4" x 40 yards Lot Size: 1 units See other DIY transformer products

AnTek Shipping Payment FAQ Description

YOU ARE BIDDING ON 1 UNIT ONLY Transformer was in service approximately 6 months in an industrial building, we moved and did not need the voltage adjustment in the new location. These cost over 250.00 each new. You must know how to wi

Triad N-64AC Isolation Transformer with Switched Add-on Outlet Offered here is a Triad N-64AC Isolation Transformer with an add-on switched duplex outlet. It is used and is in good condition. There are some scratches and small dents on the transformer.

For auction is a HITRAN control transformer from a CSI Electronics FM broadcast transmitter we are tearing down. This transformer has an input of 208 or 240 Volts with +10 & -10 Volt taps with an output of 25 Volts, it was powering the controller for the filament of a 8877 tube in an American 60 Hz. application.

MICRON CONTROL TRANSFORMER. B500BTZ13JK 500va 50/60hz Temp CL. 105C

Sola Constant Voltage Transformer CVN-1 500VA 20-13-150

Hammond Power Solutions PH500MBMH, Transformer, control, pri: 575/460/230V, 1ph, 60Hz, sec: 500VA, 115/95V, 4.35A

SAFETY ISOLATION TRANSFORMER APPLICATION Open single-phase safety isolating transformer designed and tested according to norm EN61558-2-6. Separate insulated windings and protected against dust, humidity and corrosion through complete impregnation in heat tempered varnish. For fixed installation in cabinets

The 500VA toroidal transformers are commonly used in the noise sensitive equipment or high end audio products. They are specially designed to work on all standard 115V or 230V at 50Hz or 60Hz. These transformers have heavier gauge wires then the normal requirement to avoid the copper lost during the full power output.

The 500VA toroidal transformers are commonly used in the noise sensitive equipment or high end audio products. They are specially designed to work on all standard 115V or 230V at 50Hz or 60Hz. These transformers have heavier gauge wires then the normal requirement to avoid the copper lost during the full power output.

The 500VA toroidal transformers are commonly used in the noise sensitive equipment, high-end audio products, stepper motor supply, or servo motor supply. They are specially designed to work on all standard 115V or 230V at 50Hz or 60Hz. These transformers have heavier gauge wires then the normal requirement to avoid the copper lost during the full power output.

The 500VA toroidal transformers are commonly used in the noise sensitive equipment, high-end audio products, stepper motor supply, or servo motor supply. They are specially designed to work on all standard 115V or 230V at 50Hz or 60Hz. These transformers have heavier gauge wires then the normal requirement to avoid the copper lost during the full power output.

The 500VA toroidal transformers are commonly used in the noise sensitive equipment or high end audio products. They are specially designed to work on all standard 115V or 230V at 50Hz or 60Hz. These transformers have heavier gauge wires then the normal requirement to avoid the copper lost during the full power output.

The 500VA toroidal transformers are commonly used in the noise sensitive equipment, high-end audio products, track light, stepper motor supply, or servo motor supply. They are specially designed to work on all standard 115V or 230V at 50Hz or 60Hz. These transformers have heavier gauge wires then the normal requirement to avoid the copper lost during the full power output.

The 500VA toroidal transformers are commonly used in the noise sensitive equipment or high end audio products. They are specially designed to work on all standard 115V or 230V at 50Hz or 60Hz. These transformers have heavier gauge wires then the normal requirement to avoid the copper lost during the full power output.